Axminster TS-200 Betriebsanleitung Seite 1

TS-200-2 & TS-250M-2 Basic Table SawsCode 508310Code 508312AXMINSTERSERIESHobbyAT&M: 24/02/2015REF: 508472Leg Stand501248 - TS-200-2508213 - T

Assembly10Mounting the Saw Bench to the Stand1. With assistance, place the Saw Bench (A) onto the stand. Align the four mounting holes at the base of

Assembly115. Locate the crown guard and fl exible hose (B). Remove the clamping pin bolt, washer and lift and shift handle from the crown guard assembl

Assembly1210. Remove the two clamping handles, washer from the fence assembly and place aside, remove the two coach bolt and insert them to the opposi

Assembly 1312. Locate the micro adjuster (A3), remove the end cap from the rip fence assembly (E), see fig 28. Insert the mounting blocks on the micro

Assembly14Fig 3616. Locate the flexible hose (B) and hose clips (G2). Place a clip over one end of the hose and insertthe hose over the 50mm outlet on

Assembly15Fig 394. Remove the washers/nuts from the remaining three bolts and place aside, position the bolts along the rail, put to hand four cap hea

Assembly168. Locate the rear rip fence guide rail (O), line up the holes and the machined cutouts with the ‘T’ slots to the rear of the saw table (A),

Assembly1712. Replace the rip fence assembly (E) onto the front fence rail (F). Remove the short rip fence from the main assembly by removing the four

Assembly18Fig 58Fig 59-60aW2VPre-drilled holesV2. Place an M6x16mm Hex bolt (W3) in each of the four clearance holes on both support arms (V) and loos

Assembly19Fig 64-65Carriage arm railY6. Slide the carriage table (Y) to one end of the saw table (A), place a Level across both tables and adjust the

Index of Contents2WarningThe symbols below advise that you follow the correct safety procedures when using this machine.Fully read manualand safety in

Assembly20Fig 70-71Fig 72The picture above shows the angle fence (R) removed from the carriage table for clarity.Y‘T’ Slot‘T’ BoltConnecting blockR12

Assembly21Fig 76-77Grub locking screwEccentric bushcarriage table (Y), see figs 78-79. Tighten the three lift & shift handles to lock the angle fe

Illustration and Parts Description22Basic table sawConnecting blockWork clamp blockSliding table assemblyTilt operating wheelR/H extension tableFlexib

Illustration and Parts Description23TS-200-2 Basic SawTS-250M-2 Basic Saw

Illustration and Parts Description24Tilt scale pointer and adjusting screwCarriage table scale for measuring set anglesRise and fall operating wheel a

Illustration and Parts Description25Work clamp block (A) and connecting block (B) Flip over stop assemblyFence rail scale Crown guard (A), Blade (B)an

Fig 85-86Tables ‘T’ slotSetup and Adjustment26The Riving Knife1. Raise the saw blade to its highest point and remove the saw blade crown guard, see fi

Setup and Adjustment274. The rip fence extension can be repositioned from the vertical to a horizontal position for guiding thin timber pieces through

Setup and Adjustment28If the blade is not cutting 100% true, the blade is out of alignment. Follow the instructions below on how to set the blade to t

Operating Instructions29CONNECT THE SAW TO THE MAINS SUPPLY!NOTE: BEFORE USING YOUR SAW, GO ROUND AND MAKE SURE EVERYTHING IS SECURE, FASTENED DOWN, T

What’s Included3Quantity Item Part Model Number MJ10-SB200 / MJ10-SB250 Basic Table Saw Assembly (TS-200-2 Kit Code: 508310)1 No B

Operating Instructions30Fig 103LOCK THE MITRE FENCE AND HOLD THE WORK FIRMLYFig 102THE BLADE IS SET AT AN ANGLE LESS THAN 90˚ DEGREES FOR BEVEL CUTSHO

Changing the Saw Blade316. Check the old blade for sharpness, missing teeth, resin build up, etc., clean if necessary and send for refurbishment/resha

Parts Breakdown/List32TS-200-2 and TS-250M-2 (Motor Housing Exploded Diagram)

Parts Breakdown/List33Part No Description Qty1 Set screw 12 Shaft 13 Hand wheel 14 Pin 15 Sharp 16 Pin 17 Lead screw nut 18 Motor 19 C-Spring 110 Moto

Parts Breakdown/List3474 Nut 175 Table 176 Cover 177 Screw 678 Screw 479 Pin 180 Scale 181 Lock handle 182 Screw 183 Bung 184 Hex nut 185 Flat washer

Parts Breakdown/List35TS-250M-2 (Table & Fence Exploded Diagram)

Parts Breakdown/List36TS-200-2 (Table & Fence Exploded Diagram)

Parts Breakdown/List37Part No Description Qty56 Hand wheel 157 Screw 258 Nut 159 Thread shaft 160 Plate 161 Clamp 262 Dust extraction hose 163 Base 16

Parts Breakdown/List38Sliding Table Exploded Diagram

Parts Breakdown/List39Part No Description Qty1 C-shaped ring 12 Sliding axle 13 Eccentric bush 14 Hex thin nut M8 15 Set screw M8 x 25 16 Eccentric nu

What’s Included4BCFGG2G1G3G4G6EG5Having unpacked your saw and its accessories please dispose of any unwanted packaging properly. The packaging is biod

CE Certificate40

CE Certificate41

Notes42

Notes43

Axminster Tools & Machinery LtdWeycroft Avenue, Axminster, Devon EX13 5PHaxminster.co.ukPlease dispose of packaging for the product in a responsib

Optional Accessories5HIJKLL1 L2Leg Stand (Kit Codes: 501248 & 508213)R/H Extension Table (Kit code: 508311 & 508313)Q1Q2Q3QMNOP

Optional Accessories6RS UVWW1 W2 W3 W4 R1XYTWork clamp blockConnecting blockSliding Table (Kit code: 501254 & 508214)

General Instructions for 230V Machines7Good Working Practices/Safety Primary PrecautionsWork Place/EnvironmentThe following suggestions will enable y

General Instructions for 230V Machines8Check that blades are the correct type and size, are undamaged and are kept clean and sharp, this will maintain

Specification9Code 508310Model TS-200-2 BasicRating HobbyPower 1.1kW 230V, 1phBlade Dia/Bore 205mm/30mmBlade Tilt 0° to 45°Max Depth of Cut @ 45˚