Axminster AWHBS350N Betriebsanleitung Seite 1

Axminster Tool Centre,Unit 10 Weycroft Avenue, Axminster, Devon EX13 5PHaxminster.co.ukAWHBS350N BandsawCode: 501246

Mounting the saw table Fig 1 Fig 2Remove the fence rail and put safely aside.Remove the table stabilising bolt and table insert.Fig 4Fig 5Replace the

Fitting the guide fence Fit the guide fence by clipping the rear clamp over the back rail first and dropping the front clamp over the fence rail. (See

Main saw frameUpper blade guide and guardFence guide railMitre fenceSaw table insertFloor cabinetDust extraction outletOn/Off button andswitch shroudO

Main saw frame The main body of the machine that all the other parts are mounted upon.Upper and lower The two doors that cover the upper and lower s

Blade tensioning wheelTilt mechanism clampTracking control knob Saw tableGuide fenceMotorQuadrant housingTilt quadrantDust extraction outletIdler whe

Lower blade The lower blade guide assembly is mounted on the main saw frame below the guide and table, it mounts the rear thrust bearing and two s

Micro switchDrive belt tensioning idler wheelIdler wheel adjusting knobUpper blade guide height mechanismUpper wheel mounting assemblyUpper blade gui

Lower saw The lower saw wheel and integral pulley wheel is likewise mounted on double wheel bearings, onto an axle that is mounted to a fixed base

Tilt quadrantSaw tableTable preset level stopQuadrant housingTilt mechanism clamp Tilt scale pointerScaleFig 11 UnlockLock Fig 12 Fig 11aIllustration

Mitre fenceMitre scalePointerTyp. 2‘T’ SlotSaw table insertUpper door latchUpper blade guide height clampFig 13 Fig 14Fig 13aIllustration and Parts De

Index of Contents2Index of Contents 02

Tensioning and tracking the bladeChecking the table is square DISCONNECT THE SAW FROM THE MAINS SUPPLYDISCONNECT THE SAW FROM THE MAINS SUPPLYMake sur

DISCONNECT THE SAW FROM THE MAINS SUPPLYBADLower the upper blade guide to approximately 1 1/2”(38mm) above the table. Clamp in place. NOTE: The table

To make sure the guide fence is at 90˚line up the guide fence with the edge of the table’s ‘T’ slot. If you find that the fence is out of alignment fol

1. Make sure you have read and fully understood the general instructions and safety precautions that are printed in the preceding pages of this manual

DISCONNECT THE SAW FROM THE MAINS SUPPLYPut the table back to the level position if it has been tilted. Set the upper blade guide assembly a

Daily•Keep the machine clean. •Check the saw blade for missing teeth and cracks in the fabric. •Spray oil the bare metal surfaces. Monthly•Open the l

Parts Breakdown/List26

Parts Drawing/List27

Parts Drawing/List28

Parts Drawing/List29

Having unpacked your accessories please dispose of any unwanted packaging properly. The cardboard packaging is biodegradable. Please read the Instruc

Notes30

Notes31

Please dispose of packaging for the product in a responsible manner. It is suitable for recycling. Help to protect the environment, take the packaging

The following suggestions will enable you to observe good working practices, keep yourself and fellow workers safe and maintain your tools and equipme

are being subjected to distraction. A deep cut, a lost fingertip or worse; is not worth it! Do not use this machine within the designated safety areas

Your saw is packed in the box partially assembled. This is to ensure that the components are inserted in the correct positions. e.g. The blade is fitte

Step 3Step 4Spring hinge pinPlace the door between the support and connecting plates & insert the two springhinge pins into pre-drilled holes.Loc

Step 5Step 6Screw the four rubber feet into each corner to the base of the cabinet.Tighten all the M6x12 nuts, bolts and washers before mounting the b

Lift the saw on to the cabinet, and secure using the 4 M8x40 bolts nuts and washers. ( Insert the bolts through the base of the saw, through the fl oo