Axminster AW10BSB2 Betriebsanleitung

AW10BSB2,AW12BSB2 Saw BenchCode 501196( AW10BSB2) Code 501197 (AW12BSB2)Code: 951539 AW10BSB2 AW12BSB2Table Extension SetCode: 951538 AW10BSB2 Code: 9

Fig 7Fig 8164AInitial Assembly10Adjusting boltTable supporting brackets assembledFig 5Fig 697Locate the remaining three panels (2) and 20 No. M8x16mm

Initial Assembly11Fig 12Fig 13Fig 14Fig AFig BWhen everything is tightened up, the machine can now be tipped over, towards its blind face until it is

Initial Assembly12Drive shaft for the tilt mechanismInsert the hand wheel over theshaft for the tilt mechanismFig 17Fig 18Secure the hand wheel in pla

Initial Assembly13Introduce the slot in the riving knife (14) over the two centre line bolts, behind the washers and nip the bolts to just hold the ri

Initial Assembly14Fig 29Fig 304There is no requirement to remove the guard. The profile of the riving knife precludes the use of the saw for slotting o

Initial Assembly15Locate the capping plates for the front rail (24B) and using the self tapping screws (24C), secure in place. (See fig 35) Set the fro

Initial Assembly16Locate the Rip Fence Extension (21), the two M6 x 70mm ‘T’ bolts and M6 knobs (24). Slot the two ‘T’ bolts into the fence extension

Initial Assembly17951538 10” and 951541 12” Table Extension Kits (Box 1 of 2)Select one of the extension tables (26), locate four M8 x 30mm hexhead bo

Initial Assembly18Locate the long Rip Fence (front rail) (32) and (back rail) (33), remove the short rip fence front and back rails (22-23) from the s

Initial Assembly19Fig 5627Screw the threaded rubber foot (28) on to the end of the support leg (27), until it’s tight. (See fig 57) Unlock the caphead

Index of Contents02Index of Contents 02Declaration of Conformity 03Parts Index 04-05-06General Instructions for 230V Machines 06-07Specification 08

Initial Assembly20951539 10” and 12” Sliding Table Kits (Box 1 of 2) and (Box 2 of 2)Locate and identify the mounting brackets (35) and the height adj

Initial Assembly21Locate the slide rail assembly (40), orientate it so that the longest rail is at the top, and the channels etc., of the extrusion a

Initial Assembly22Locate the sliding table assembly (38) and manoeuvre the bearing bogies onto the rails (40), slide the table onto the rails and posi

Initial Assembly23Lower the fence mounting (43) onto the rear quadrant NOTE: position the fence so the sacrificial plastic orange tongue is against the

Setting the Machine24Setting the TablesFig 84Fig 85Setting the Sliding TablesNOTE 1. With the bracket fixing bolts in a loose condition ensure that the

Setting the Machine25The overall setting process is done in 3 phases. 1) Setting the table level against the main table; front and rear. 2) Setting th

Setting the Machine26Set the sliding table so that the front edge is inline with the front edge of the saw table. Place a long straight edge (a bit mo

Setting the Machines27Raise the blade to its maximum height, check that is upright to the table. Set the sliding table fence to zero angle against the

Setting the Machine28Tilt the blade fully over. Using a mitre square, set the angle of the saw to 45˚. Check that the index mark gives a corresponding

Setting the Machine29Check the belt tension, see figs 106-107, the belt should be tight, but not unduly so. Remove all tools and stow away. Check that

Declaration of Conformity03Copied from CE CertificateThe undersigned, F. Nispel authorised byLaizhou Fulin Machinery Co., Ltd.No. 275 Wenquan East Road

Setting the Machine30Specific Instructions/Precautions for the Saw BenchConnect the machine to the mains supply, lift the switch shroud and give the ma

Specific Instructions/Precautions for the Saw Bench31Operating Instructionsthe blade ensure that the push stick is to hand, and you use it. Remember t

Illustration and Parts Description3212310404538414325322111132042Extension lock 1. Saw Bench 25. Micro Adjuster Assembly 2. Front and Side Panels

Illustration and Parts Description333814 37674282733322617Table Extensions Setup 1Table Extensions Setup 2

Illustration and Parts Description34NVR “ON” and “OFF” switch assemblyRise and fall control locking handle (1) Tilt angle lock (2)12223Tilt control ha

Changing the Saw Blade35Raise the saw blade to it’s highest point. Remove the saw blade guard. Remove the 5 screws that secure the table insert, place

Changing the Saw Blade36MaintenanceTighten up the saw nut, using the tommy bar to hold the shaft steady. Check the riving knife is aligned with the sa

Wiring Diagram37

Parts Breakdown/List 38DIAGRAM A

Parts Breakdown/List39NO. DESCRIPTION QtyA-l Front panel 1A-2 Left frame 1A-3 Side panel 2A-4 Real panel 1A-5 Right frame 1A-6 Left leg 1A-7 Front sid

Parts Index04 Model Number: MJ2325D/MJ2330D501196 10” and 501197 12” Saw Bench (Box 1 of 2)1 off: Saw Table on upper chassis (with motor, table ins

Parts Breakdown/List40DIAGRAM B Part 1

Parts Breakdown/List41DIAGRAM B Part 2

Parts Breakdown/List 42NO. DESCRIPTION QtyB-l Rear rail 1B-2 Step blot N8X25 10B-3 Cross recessed countersunk head screw M5X65B-4 Insert 1B-5 Worktabl

Parts Breakdown/List43DIAGRAM CNO. DESCRIPTION QtyC-1 Lock handle for miter gauge 1C-2 Large washer 8 1C-3 Mitre gauge 1C-4 Cross recessed pan head sc

Parts Breakdown/List44DIAGRAM D

Parts Breakdown/List45NO. DESCRIPTION QtyD-1 Blade nut M16(（left-hand)（ 1D-2 Outer blade washer 1D-3 Blade 1D-4 A-blet 1D-5 Pulley 1D-6 Key（ (A-type)（

Parts Breakdown/List46DIAGRAM ENO. DESCRIPTION QtyE-1 Round head rhvetwhthsamall head ɸ3x7 2E-2 Hexagon nut M8 1E-3 Washer 8 1E-4 Round head screw ɸ 3

Parts Breakdown/List47DIAGRAM FNo. DESCRIPTION QtyF-1 Sliding table 1F-2 Long round rail 1F-3 O-shape rubber ring ɸ20 2F-4 Stop block 2F-5 Cross reces

Parts Breakdown/List48DIAGRAM GNo. DESCRIPTION QtyG-1 Self-locking handle M8X25 1G-2 Stop block 1G-3 Hexagon socket set screw M5x12 1G-4 Stop board 1G

Notes49

Parts Index05501196 10” and 501197 12” Saw Bench (Box 2 of 2)1 off: Rip Fence Assembly (partially assembled)1 off: Rip Fence Extension1 off: Short Rip

Notes50

Notes51

Axminster Tools & Machinery LtdWeycroft Avenue, Axminster, Devon EX13 5PHaxminster.co.ukPlease dispose of packaging for the product in a responsib

Parts indexGeneral Instructions for 230V Machines06951539 10” and 12” Sliding Table kits ( Box 2 of 2)Mitre Angle Rear Quadrant (with lift and shift h

General Instructions for 230V Machines07UNDER NO CIRCUMSTANCES SHOULD CHILDREN BE ALLOWED IN WORK AREASt is good practice to leave the machine unplugg

08SpecificationInitial AssemblyPlease read through the Section entitled Parts identification and Description, this will enable you to more readily ident

Initial Assembly09PLEASE RECYCLE ANY UNWANTED PACKAGING RESPONSIBLYSaw Body AssemblyHaving unpacked the boxes, put the parts and components where they