Axminster AWSMS102 Bedienerhandbuch

AWSMS102 250mmMitre Saw Axminster Tool Centre,Unit 10 Weycroft Avenue, Axminster, Devon EX13 5PHaxminster.co.uk Code: 501243

Extension Arm/Cut Length StopLocate the two ‘U’ clamps, extention arms and the cut length stop assembly. Slide the cut length stop ontothe right exte

Identification and Parts DescriptionGuard latchSaw arbor lock buttonTurntableHold down clampTilt preset stopMain Saw ChassisLaser switchDust bagMitre

12Identification and Parts DescriptionOperating handle The operating handle contains the interlocked trigger switch and the laserOn/Off button switch

13Identification and Parts DescriptionOperating handleHandleTrigger switchTilt housingCut length stop mountingSaw body frameLock down pin2mmLower guar

14Identification and Parts DescriptionTurntable Mounted into a circular recess in the main saw chassis, the turntable also mounts the extrusion that c

Identification and Parts Description Fence This is an aluminium casting bolted to the rear of the saw table. It has various cut-outs and shapes ma

Adjusting the SawLocate and loosen the 4 bolts that hold the fence to the chassis. Adjust as necessary until thefence is square to the blade. Tighten

Tilt pointer0˚ degreesFig IFig JMitre Saw at 45˚ degrees45˚degreesTilt preset stopEngineers squareTilt clamping leverFig G Fig H17Adjusting the Saw

18Operation of the LaserSetting the LaserThe laser fitted to the AWSMS102 Sliding Mitre Saw provides a convenient visual guide for liningup the saw bl

Setting the Laser19Laser toggleswitchTo adjust the laser, loosen thecaphead screw on the holderTo adjust the mounting bracketloosen the caphead boltFi

Index of ContentsPage No.Declaration of Conformity02Please read the Instruction Manual prior to using your new tool; as well as the operatingprocedure

Changing the Saw Blade201. Locate the two screws as indecated holding the front of the saw guard bracket, and loosen and removethem to allow the saw

21Changing the Saw Blade2. Before fitting the new blade ensure that the inner saw blade washer is clean and correctly seated on theshaft. Fit the blad

Parts Breakdown/List22

23Identification and Parts Description

24Identification and Parts Description

25Identification and Parts Description

Identification and Parts Description26

27Notes

Please dispose of packaging for the product in a responsible manner. It is suitable for recycling. Help to protect the environment, take the packaging

03What’s in the BoxModel Number: MJ2625IIIA 1 No: 250mm Sliding Arm Compound Mitre Saw1 No: 250 Saw Blade (fitted)1 No: Arbor bolt spanner5 No: Rubb

04SpecificationModel AWSMS102Product Code 501243Rating HobbyPower 1,500WElectric Brake YesSpindle Lock YesBlade Dia/Bore 250mm/30mmBevel Angle Range 0

05Table of CapacitiesAlways use (250mm) saw blades with a rated speed in excess of 4,500 r.p.m. The machine is suppliedwith a 250mm GP (40 tooth) Saw

06General Instructions for 230V MachinesThe following suggestions will enable you to observe good working practices, keep yourself andfellow workers s

07General Instructions for 230V MachinesOnce the saw is mounted, carry out any setting operations, (mitre, tilt..?), and remove all toolsused in the s

General Safety Precautions for Mitre SawDO NOT change blades with power connected. Always use the correct accessories;especially the correctly sized s

09General Safety Precautions for Mitre SawDO NOT allow the saw to 'stall'; if unfortunate circumstances cause the machine to stall, switchof