Axminster WS1000TA Spezifikationen

WS1000TASpindle MoulderAxminster Tool Centre,Unit 10 Weycroft Avenue, Axminster, Devon EX13 5PHwww.axminster.co.ukCode: 501209

10AssemblyLine up the edge of the steel plate (C3) with the ‘T’ slot machined into the sliding table A see fig 3. Slide thesupport table assembly (C)

11AssemblyFig 7 Fig 8 Fig 9 Fig 10 B4B6B7A‘T’ slotFig 11 Fig 12 B1B6Machined slotsPre-drilled holesPinsNuts & washersFig 13 Fig 14 B3B1A

12AssemblyFig 15 Fig 16B5Locate the two M6 x 11mm caphead screws (B5), line up the extention table support rod (B7) bracket with thepre-drilled holes

13AssemblyLift & shift handle pin lockTurn butterfly knob tolock the fenceTurning the handle tolock pinFig 21 Fig 22 Fig 19 Fig 20 B2B1Pin90˚ Sto

14AssemblyFig 25 Fig 26Fig 27 Fig 28 D1D2D1Circular ringsFig 29 Fig 30 Locate the guide assembly mounting bracket (D3), using a 6mm allen key remove

15AssemblyE4E5D3Guide AssemblyStep 4 Slide the guide arm (E1) through the mountingbracket (D3)Clamp the guide arm with the clamping knob(E2) and lift

16AssemblyMi tre Fence Work Clamp AssemblyStep 5 Fig 35 Fig 36 Fig 37 Fig 38 Fig 39 Fig 40 Locate the pre-drilled metal plate (F3) & slot it int

17Illustration & Parts DescriptionA Spindle Moulder D Spindle Guard AssemblyB Sliding Table Extention Assembly Optional E Guide AssemblyAccessory

18Illustration & Parts DescriptionB1 Extension table castingB2 Extension table fenceB6 Pivot armB7 Extension tablecasting support rodC1 Steel benc

19Illustration & Parts DescriptionE3 Lift & shift handleE2 Clamping knobE1 Guide armD3 Guide assembly bracketAnti-kickbackclamping knobGuide r

02Index of ContentsPage No.Index of Contents 02 Declaration of Conformity 02What’s Included 03-04-05-06Optional Accessories 03Genera

20Illustration & Parts DescriptionSpindle moulder control panelNVR ON/OFF switchFig 41 Fig 42 Reversing selector switchEmergency stop shroud, slap

Illustration & Parts DescriptionThe extension table fence set to 45˚Extension table angle scaleFig 47 Fig 48 Distance stop assemblyTelescopic ext

22Setting Up the MachinePlace a 90˚square up against the fence and check it is perpendicular Fig 55 Fig 56 Adjust the advancing knobs (b) until bothf

23Setting up the MachineAGF5mmFig 59 Adjusting the feeder roller & ant-kickback assemblyFig 61 Fig 60 Loosen the feeder roller clamping knobs (a a

24Installing/Changing the Spindle Moulder CutterChanging the spindle moulder cutter Fig 66 Fig 67 Raise the spindle to the maximum height by unlocking

25Changing the Spindle Moulder Speed Fig 68 Fig 69 Fig 70 Fig 71 Open the motor access door to the front of the machine, by removing the two caphead

26Positioning the Machine The spindle moulder can be used as a sander by attaching a sanding drum to the spindle, please follow theinstruction below

27Using a Sanding DrumWorkpiece Handling•Feed the workpiece straight across the machine table, holding the fingers close together and guiding the work

28Optional AccessoriesSliding Table Extension AssemblyTenon PlateFig 74 Fig 75 The spindle moulder can be fitted with the followingoptional accesso

29Optional AccessoriesMajor ServiceAfter several months of constant use the condition of the chains, sprockets and tension of the drive belts and thet

03What’s IncludedQuantity Item Model Number1 off Spindle Moulder A MX5110ASupport Table Assembly C1 off Support Table C12 off Lift & Shift Handle

30Trouble ShootingDISCONNECT THE MACHINE FROM THE MAINS SUPPLY!

31Wiring Diagram

32Parts List/Drawings

33Parts List/Drawings

34Parts List/Drawings

35Parts List/Drawings

36Parts List/Drawings

37Parts List/Drawings

38Parts List/Drawings

39Parts List/Drawings

04What’s IncludedABB1B2B3B4B5B6B7

40Parts List/Drawings

41Parts List/Drawings

42Parts List/Drawings

43Parts List/Drawings

Please dispose of packaging for the product in a responsible manner. It is suitable for recycling. Help to protect the environment, take the packaging

05What’s IncludedCDEE1E2E3E4E5D1D2D3C1C2C3

06What’s in the BoxGood Working Practices/ Safety The following suggestions will enable you to observe good working practices, keep yourself and fell

Authorised UseThis machine is designed for shaping wood and woodderived materials.Machining of other materials is not permitted and maybe carried out

08Specific Safety PrecautionsGeneral Safety NotesWoodworking machines can be dangerous if not usedproperly. Therefore the appropriate general technica

09AssemblyUnpack all the boxes and check all the componentsagainst the “What's in the Boxes' List. If any parts orcomponents are missing, pl